Tuesday, 8 September 2015
Exhaust manifold and Turbo . . .
Today I started on my second exhaust manifold for the 2nd engine. first I had to fit the Turbocharger to the Engine with a 20mm adaptor plate. This was a bit of hard work cutting milling and filing to get the right shape.
anyway it all fits now and the reason for a 20mm plate is the waste gate pivot that I will put in when I am shore of the right place.
Today I started on my second exhaust manifold for the 2nd engine. first I had to fit the Turbocharger to the Engine with a 20mm adaptor plate. This was a bit of hard work cutting milling and filing to get the right shape.
anyway it all fits now and the reason for a 20mm plate is the waste gate pivot that I will put in when I am shore of the right place.
Sunday, 6 September 2015
This tube is from the Turbocharger to the Ice intercooler. I had to solder 2 tubes into the main tube one for the air temp sensor and the other to the dump valve. All this work had been finished and then I realized that the air temp sensor would create a lot of drag in the original position so today it was moved to the inner side of the tube
Wednesday, 2 September 2015
This photo is of the 6th gear light that will reminded me that I am in 6th. it could be so easy to go flat out in 5th by mistake what you need to remember is there is nothing to judge your speed to get a idea
what it will be like the turbocharged Engine screaming your hear down and the view you will see imagine if you sat on the beech looking out to sea absolutely nothing in your way just marker flags every 1/4 mile
this light is activated through the Motec ECU and the gear position sensor this sensor is one we adapt from a standard Yamaha neutral switch and it will indicate to the ECU all 6 gears
the light consists of 3 neon lights 1 stainless steel tube a plug and some wire
you will have to excuse my spelling it can be bad but I hope you can work around this
what it will be like the turbocharged Engine screaming your hear down and the view you will see imagine if you sat on the beech looking out to sea absolutely nothing in your way just marker flags every 1/4 mile
this light is activated through the Motec ECU and the gear position sensor this sensor is one we adapt from a standard Yamaha neutral switch and it will indicate to the ECU all 6 gears
the light consists of 3 neon lights 1 stainless steel tube a plug and some wire
you will have to excuse my spelling it can be bad but I hope you can work around this
Sunday, 2 August 2015
finished Throttlebodies.
As you will see from the photograph below the throttlebodies for the spare engine are now finished. If you look at them in fine detail you may wonder why some of the bolts are protruding out, I always leave bolts a little longer than necessary on my Bonneville bike because if you had a bit of bad luck and the bolt was to become loose, it may just give you time to spot the fault and rectify it before the bolt fell out completely.
On the RC injectors where the fuel pipe fits I had to do a little modification to the end of the injector to allow the fuel pipe to go further on for a more secure fit. Also, the original Kawasaki retainers had to be cut down by one millimeter for the best fit possible.
I had to devise a method of cutting down the air-intake rubbers from the air box to the throttlebodies and I came up with this idea of sliding the rubber hose over a plastic tube then inserting a steel bar into the plastic tube, then clamping the plastic tube into the lathe, the steel bar preventing the plastic from crushing and with the lathe spinning, applying a Stanley knife onto the rubber gave a lovely straight cut pipe.
On the RC injectors where the fuel pipe fits I had to do a little modification to the end of the injector to allow the fuel pipe to go further on for a more secure fit. Also, the original Kawasaki retainers had to be cut down by one millimeter for the best fit possible.
I had to devise a method of cutting down the air-intake rubbers from the air box to the throttlebodies and I came up with this idea of sliding the rubber hose over a plastic tube then inserting a steel bar into the plastic tube, then clamping the plastic tube into the lathe, the steel bar preventing the plastic from crushing and with the lathe spinning, applying a Stanley knife onto the rubber gave a lovely straight cut pipe.
Subscribe to:
Posts (Atom)